Our Products

STEEL MEDIA

Vibra Finishing Solutions

STEEL MEDIA

Steel media can be used for light deburring as well as peening. Peening surfaces work-hardened by imparting compressive stress resulting in longer part life and higher wear resistance. Peening action reduces porosity while boosting corrosion resistance. Stainless and carbon steel media are available.

Category Steel Media Tag Media

SHAPES

SPECIFICATIONS

SHAPES

SPECIFICATIONS

Challenges we’ve solved in the past

Vibratory Peening

Kumar Balan explores the efficacy of vibratory peening, its financial viability and its potential market reach. His article will cover all these aspects courtesy of data provided by Vibra Finish.

In the winter 2018 issue of The Shot Peener, we discussed two non-conventional peening techniques; one of which was Vibratory Peening. In addition to the superior surface finish, we learnt that the layer of compression was deeper with vibratory peening when compared to conventional shot peening. The process itself was significantly different from conventional peening in terms of media life, dust generation and utility costs. We concluded that this technique of generating residual compressive stress was worth further exploration. The results are discussed here.

Vibra Finish, a company based in Mississauga, Ontario (Canada) has conducted multiple studies to validate the established facts and clearly define limitations of this peening process. They have attempted to identify components, both industrial and domestic, that demand and could benefit from a combination of fatigue resistance and superior surface finish, both in a single step process.

When reviewing a new process, especially one that simulates an established technique albeit with marked improvements, skepticism is common. Such doubts include the technical efficacy of the process, financial viability and its potential market reach. Our discussion will cover all these aspects courtesy of data provided by Vibra Finish. Given that Vibra Finish operates conventional shot peening machines as well, our discussion is enriched by the comparison of both techniques under identical process variables.

Background

Vibratory finishing is a primary process in its own right and sometimes it is a supplementary process used to polish a shot-peened surface. As a secondary operation, it can eliminate surface roughness created during peening. Surface roughness, greater than a certain application dependent value, can have a detrimental effect on the fatigue life of the component. As we know, most specifications limit material removal in post-peening finishing to 10% of the ‘A” intensity value. Vibratory finishing could be controlled to stay well within this tolerance. Vibratory finishing is also used for deburring, burnishing, descaling and is ideal for finishing parts prior to painting, plating, heat treating, anodizing or simply to achieve an excellent final finish.

Vibratory finishing is categorized as a “mass-finishing” process, and when designed properly, will result in a batch of parts that is treated with uniformity and consistency. The process is not reliant on operator skill unlike certain other techniques such as buffing, filing, belting, etc. Instead, a batch of parts are loaded in bulk into a tub or continuously fed to a vibratory machine for inline operation. The tub is filled with finishing media and suitable compound(s) that when combined act as thousands of small filing surfaces scrubbing the parts. The compound assists the cleaning/finishing action of the media (usually made from ceramic). The choice of compound will depend on the material to be treated, the desired surface finish, and the individual application and process requirements. Additives in the compound could serve other purposes such as alkaline cleaning, acidic burnishing, washing and rust inhibition.

Just like any other process, vibratory finishing has controllable variables that alter the finish quality. Two of the main factors include the amplitude and frequency of vibration. Given the advantages of this process, it is a natural progression that vibratory finishing be extended in its application range to provide a peened and finished product in a single step.

Past Research

In 2016-17, Dr. Hongyan Miao and Prof. Martin Levesque from Polytechnique Montreal studied the fatigue life improvements of a certain alloy type using conventional peening and shot peening. The results from this test were encouraging enough to carry out further testing. The details of their testing are as follows:

Conventional shot peening was carried out in an Automated air type machine with a V2″ diameter nozzle propelling Z425 ceramic bead on the component. The target intensity was 8A, achieved at an air pressure of 20 PSI and media flow of 10 lb./minute. The part was fixtured on a rotary table.
Vibratory peening (this term is used to signify the sole purpose of this operation-peening) was performed in a batch-type tub filled with AISI Type 1018 Carbon Steel balls with diameters 1/8″, 3/16″ and Vi”, adding up to almost a ton in weight. The target intensity remained unchanged from 8A as in the conventional peening machine.
It is interesting to note the mix of media sizes in this process as compared to conventional shot peening where the reliance is on consistent media size, to the extent of using classifier screens to maintain the same in the machine. Due to proprietary nature of this process, further elaborations on the use of multiple media sizes is not readily available. A reasonable explanation would be to consider the mechanism of media movement in a batch-type tub, and the interaction of one size with another much like on a pool table. This is compared to conventional peening where a steady stream of media impacts the target.
Both media types (ceramic and carbon steel balls) were of comparable hardness in the range of 60 HRC.
In contrast to conventional shot peening where the part spinning on the table was targeted by the abrasive, the part in the vibratory tub was positioned 10″ below the ball bed surface with constant contact of the carbon steel balls.

The team plotted saturation curves using data sets obtained from both peening techniques and, with their distinct process parameters, they arrived at an intensity of 8.3A and 8.6A with shot peening and vibratory peening respectively. Residual stress measurements carried out on the test parts using X-ray diffraction displayed some interesting results. Shot peening produced a larger surface and maximum compressive residual stress (-212 MPa and -297 MPA respectively), as compared to -148 MPa and -225 MPa produced with vibratory peening. However, the difference was in the depth of compression. Vibratory peening produced -50 MPa at 520 micron below the surface whereas with shot peening, the same magnitude of residual stress, -50 MPa, went only 340 micron deep into the surface. In practical terms, if we are able to alter the process parameters in vibratory peening so that it generates the same magnitude of compressive stress as shot peening, we can expect this stress to stretch over a greater depth than with shot peening.

The surface roughness results were as expected. The study compared the surface roughness of the sample part as machined, shot peened and after vibratory peening. Roughness was tested on three samples, on three individual locations and the trend was the same in all cases. One such set of results is documented below for brevity.

Fatigue tests performed as part of this study generated similar average fatigue lives for both processes. However, they did find that the values from shot peening had significantly less standard deviation (minimal variation). The study concluded that rather than comparing similar Almen intensity values, future studies should compare the fatigue life measures for similar residual stress profiles, at different levels of roughness. Ultimately, the measure of all such processes is based on the extent to which fatigue life has been impacted, preferably in the positive direction.

Commercial Components and Vibratory Peening

Encouraged by the results of the previous tests, Vibra Finish continued with comparative tests on more conventional components – a turbine blade and an automotive transmission gear. The tests were to study the following:

Compare the effects of shot peening and vibratory peening on (a) open and (b) relatively closed geometries in order to learn the limitations presented by certain part types to this process.
Surface roughness
Residual stress and nature of curves (relieving of compressive stress as measured into the depth of the part)

The conventional shot peening process was carried out in an automated airblast machine under the following process parameters: Target intensity: 10 to 12A and 100% coverage. This was achieved using SI 10 regular hardness steel shot propelled at 30 PSI by a Vi” diameter nozzle at a stand-off distance of 8″ for a time cycle of 30 seconds.

Vibratory peening was carried out using single size, 3 mm diameter steel balls, in a batch type tub for a total cycle time of 10 minutes. Two sets of data, one for surface roughness and the other for residual stress (using X-Ray Diffraction) were analyzed.

Surface Roughness Data:

The surface finish results show an interesting trend in a relatively closed geometry component (gear) when compared with the blade with wide, open surfaces. The root section of the gear, which is the area of maximum stress concentration, is the most important region for measurement. In this region, the shot peened component exhibited a much rougher surface finish when compared to an identical vibra-peened component. All other regions of the gear such as the drive face, coast face and tip showed comparable surface roughness values in both processes. Geometry of the gear tooth, media access and media size could all be factors that might have contributed to the final roughness value in vibratory peening.

Though S110 was ideally suited to peen the smallest radius of the gear tooth without causing coverage issues, the surface roughness ended up much higher than with vibratory peening. However, we have to consider the fact that in order to achieve the same intensity (8 to 12A), the S-110 would’ve had to penetrate deeper than the 3 mm balls in vibratory peening, resulting in a rough surface profile.

A study of the residual stress profile provided further insight into the characteristics of both processes to induce compression in the parts.

Gear

The residual stress curve for this component is different from the classic “J” hook curve that was expected before the results were obtained. Also, this is a carburized component that may not necessarily show high values of residual stress when shot peened with SI 10 size media to a relatively lower intensity range (8 to 12 A). Though the residual stress at the surface of the shot peened sample is greater than that achieved with vibratory peening, the dissipation (or loss) of residual stress towards the depth of the material is much more controlled with the vibratory peened sample. Vibratory peening did record a seemingly anomalous reading when measured at 0.0008″ depth, registering a steep 33% drop from -79 ksi to -53 ksi before continuing with a controlled and gradual decline at deeper levels into the sample.

An obvious question that remains to be evaluated is whether the surface finish (roughness) was the cause of this steep drop in residual stress in the shot peened sample, especially considering the smoother surface after vibratory peening. The gear being carburized might have also led to the relatively lower magnitude of residual stress using both types of peening techniques.

Blade

A blade from a turbine wheel was chosen for its open geometry. As it turned out, the resultant residual stress followed the all-familiar J-hook pattern. Surprisingly, the compressive stress generated at the surface was greater with vibratory peening when compared to the shot peened sample. Once again, the open geometry of the part and material properties (softer than the gear) likely caused this result. An interesting observation is to be made at 0.0021″ depth where both processes register the maximum compression. Assuming the shot-peened part had developed a rough profile after peening, if one were to polish it by 10% of the ‘A” intensity value, i.e., 0.0011″, we will end up with a higher residual stress value (about -140 ksi) at the surface of the shot peened part. At this depth, the vibra-peened part will have a residual stress of-113 ksi without the need to be polished.

The drop in residual stress when going deeper into the component was drastic with the shot-peened part and followed a gradual decline with the vibra-peened component. This is a positive attribute of the latter process.
In both cases, it appears that the geometry of the part played a big role in generating increased magnitude of residual stress.

Conclusions and Future Steps

Vibratory peening certainly shows a lot of promise in terms of combining the two essential features in surface finish— smooth profile and compressive stress—in a single step. Moreover, in both examples, it has shown a gradual and smooth dissipation of this stress as one travels deeper into the material, demonstrating the controllability of the process. The next steps are to study the operating cost of both processes to assess the financial viability of the process. Vibratory peening does not possess the same consumable pattern that we are all familiar in conventional shot peening. This is also true in terms of capital costs involved in procuring a conventional shot peening machine.

Vibratory peening has yet not been governed by a specification. This might be the next step to increase the adoption of this process in known sectors. Meanwhile, a whole range of consumer parts could greatly benefit from this combined process.

About Vibra Finish

Vibra Finish, located in Mississauga, Ontario, Canada, offers a full range of vibratory finishing services and equipment. Their services include deburring, burnishing, descaling, vibrapeening, polishing, rust removal, cleaning, drying, corrosion protection, and peening services. Visit: vibra.com for more information.

Source: The Shot Peener

Choosing Tumbling Media

A common deburring machine used for mass-finishing parts is a vibratory deburring machine, or vibratory tumbler, which utilizes abrasive tumbling media to deburr, clean, or polish unfinished or dirty parts or objects. At Vibra Finish, the abrasive media and unfinished or dirty parts are put inside a large drum. The drum vibrates, driving down the contents in a circular motion, mixing everything together. The unfinished or dirty parts are subsequently deburred, cleaned, or polished by friction with the abrasive material.

The kind of deburring, cleaning, or polishing desired and the part characteristics will determine the type, size, and shape of the abrasive media used. Some common types of tumbling media are abrasive steel, ceramic, organic materials, and plastic. These materials can be purchased in a variety of shapes such as cylinders, cones, stars, pyramids, wedges, spheres, ovals, and other forms, depending on the function needed. Openings in the parts will determine the size and shape of the media used. To prevent media lodging in the part, it should be a minimum of 70 per cent of the size of the hole or slot. This avoids two pieces getting stuck side by side in the piece.

Here are some common uses for abrasive media in the Vibra Finish process:

Steel Media – Use for heavy deburring, or shining, polishing, and burnishing metal, plastic, or ceramic parts. Since plastics have a high abrasion resistance, resulting in a matte finish after deburring, a second, polishing step is often required.
Ceramic Media – Use for light and heavy deburring and when fast deburring is needed. Good for hard, heavy metals (such as steel or stainless) and to remove rust on parts. Use for general-purpose polishing. Plastic, steel, stainless, and aluminum parts are often polished using ceramic media. Use ball shapes to polish aluminum to avoid nicks.
Plastic Media – Use for general metal deburring, precision deburring, polishing, and burnishing. Use on softer metals such as aluminum or brass and on threaded parts.
Organic Media (Walnut Shells, Corn Cob) – Use walnut shells for medium-to-light deburring. For light finishing and polishing, use walnut shells and corn cob meal. To clean and dry wet or dirty parts, use organic media. Corn cob is particularly desirable in finishing some metal parts because of its ability to absorb surface oils on the parts. Utilizing organic media is advantageous because they are natural, safer for the environment, biodegradable, durable, and reusable.
Wet tumbling compounds – Used by mixing with solid media to deburr, finish and polish parts, their function is to clean, enhance deburring, and for corrosion and rust protection.

Abrasive media for deburring equipment wears down slowly, but will vary on how aggressive the media is. Also, the smaller the media, the better the finish, but the longer it will take. The larger the media, the faster it will deburr. Having the correct media and the deburring machine full of parts is the key to successful finishing.

To learn more, please contact Vibra Finish.

Vibra-Glo Compounds

Vibra Finish has mastered every aspect of the metal-finishing process – including cleaning, polishing, smoothing, and deburring – making it Ontario’s go-to source for industrial finishing. But the company’s services also extend to selling a variety of media, compounds, and other materials to help customers with their private finishing applications. The Vibra Finish inventory includes 13 types of Vibra-Glo compounds for various applications, from burnishing to rust removal.

Cleaning, Smoothing, and Polishing Surfaces

Vibra-Glo compounds play an important role in the finishing process. Users throw these finishing compounds together into a system with water and media, and the machine’s sliding or tumbling action causes the compounds to clean, polish, and smooth the surfaces of the metal parts.

Wet compounds are available from Vibra Finish. They typically come in a paste form or are used with water in wet finishing processes. In addition, these compounds are formulated with properties that are tailored specifically for use in either tumbling barrels or vibratory systems.

Vibratory compounds are designed for finishing in vibratory machines, which are usually relied upon for thorough cleaning and deburring of delicate parts or parts with bores or recess that are difficult to reach. These compounds are also well suited to large surfaces. Adding a vibratory compound, along with selected media, to a vibratory machine that contains parts for mass finishing causes the machine’s rubbing action to have an abrasive effect on the parts, helping to clean them more effectively. Another benefit of compounds is their suspension properties, which stop the debris that arises from depositing back on the parts, thereby keeping the abrasive action constant.

The lineup of Vibra-Glo compounds available includes five types of rust inhibitors, two alkaline cleaners, two all-purpose cleaners, two mild acidic burnishers, and one type each of powdered concentrate and washing compound. The range that Vibra Finish carries is ample evidence of the many ways compounds benefit the finishing process.

Trust Vibra Finish compounds for a better finishing job every time.

To learn more, please contact Vibra Finish.

Sandblasting Advantage

For close to half a century, Vibra Finish has offered industrial metal-finishing services above and beyond customer expectations. The company’s many skills including burnishing, surface engineering, deburring, rust removal, and vibratory finishing. Another key example is metal blasting – a process for cleaning or finishing surfaces with a special tool that shoots out pressurized abrasive material at high speed. This method offers three major advantages: effectiveness, economy, and versatility.

Cleaning Dirt and Debris Thoroughly

Blasting is renowned for its effectiveness; it can clean dirt and debris thoroughly, while also grinding rust, paint, and corrosion from metal surfaces to result in the best possible finish.

Economy is another key benefit of metal sandblasting. The Vibra Finish team conducts blasting before finishing in order to replace sanding, wire brushing, and pickling. Since this method cleans the surface mechanically, often no other cleaning is typically necessary, which saves plenty of time. Blasting can be up to 75 per cent faster than hand cleaning, and the abrasives for blasting are relatively inexpensive and reusable. In addition, blasting offers high productivity per hour per dollar of equipment.

Finally, metal blasting is very versatile. It can accomplish many different kinds of finishes, and the final effect depends on the hardness of the abrasive, its particle size, the speed of the abrasive stream, the angle of the abrasive gun and its distance away, the method of application, the workflow, and other factors. The user can choose from a broad variety of abrasives such as aluminum oxide, plastic abrasives, silicon carbide, corn-cob grit, and glass beads to achieve different outcomes; for example, abrasive grits leave a dull satin finish, while glass beads texturize, descale, remove light burrs and die-cast flash to create a smooth, bright satin finish.

To learn more about sandblasting options and advantages, contact Vibra Finish.

Mass Finishing Parts

Vibra Finish has served Canadian businesses since 1971 with the most diverse range of finishing services and skills. One key edge that makes the company successful is its unmatched collection of finishing machinery. Our Ontario facility is equipped with machinery to handle any mass-finishing task a customer may demand. Not only does the Vibra Finish crew use this range of equipment for its own services; the company also sells new and used finishing machinery for customers’ private use.

More than 150 units

To meet its clients’ needs, Vibra Finish has four plants that offer production finishing every day, with more than 150 machines. Services offered include deburring, burnishing, peening, vibropeening, polishing, rust removal, cleaning, drying, and anti-corrosion protection. The diversity of the company’s finishing machinery also enables it to offer vibratory, tumbling, centrifugal finishing, washing, blasting, packaging, and assembly.

The Vibra Finish team uses the following five types of equipment:

Vibratory Bowls. Different styles of vibratory bowls work for varying applications. Batch bowls produce shorter cycles with a quicker turnaround, while flow-through bowls create a uniform action in the machine with maximum dwell times. Flat-bottom bowls offer top vibratory efficiency and better ergonomic design to optimize productivity.
Vibratory Dryers. The company’s corn-cob dryer transfers heat directly with efficient electric heating elements, with a temperature controller that offers heat when necessary. While intended as standalone machines, vibratory dryers can be connected to vibratory deburring or burnishing equipment.
Vibratory Tubs. Vibra Finish typically uses long, low-profile tubs for long, narrow parts; some have compartments that keep parts from contacting each other. Users can process larger parts in deeper-profile tubs. Vibratory tubs are also useful for part-on-part self-tumbling.
Centrifugal Finishers. These are recommended for small, flat parts that may stick together. Centrifugal finishers have treatment intensity up to 20 times higher than those of standard vibratory-finishing processes.
Material-Handling Equipment. This group includes bin dumpers, conveyors (some with hot air blow-off), dip tank drag-out systems for rust removal, and load hoppers, all used to expand and automate the finishing system.

To learn more, please contact Vibra Finish.

Vibra Finish Tips

Vibra Finish has logged close to half a century of experience in finishing metal parts for Canadian businesses. Their process involves altering the components’ appearance through smoothing, polishing, deburring, and/or cleaning. Plastic and synthetic media combined with Vibra’s compounds are very effective at creating a desirable finish on softer materials, such as aluminum. Vibra Finish suggests that users place parts into a vibratory finishing machine with media and compound, so that the parts rub against the media with the compounds’ assistance. The result is a strong smoothing effect.

Better deburring and smoothing

There are many types of compounds and plastic and synthetic media for sale in Vibra Finish’s catalogue. The Vibra Finish team uses these products in its own finishing services, to get top results.

Also known as tumbling stones, synthetic and plastic deburring media come in different preformed shapes and with varying degrees of abrasive content. This lightweight media is perfect for applications requiring soft, abrasive finishing or involve brass or aluminum parts. They also work for general-purpose deburring, pre-painted finishing, and quick, heavy cutting. Although shine is minimal, finishes are smooth.

Plastic and synthetic media comes in several shapes from Vibra Finish: cones, pyramids, wedges, or triangles. Triangles work best for corners and flat surfaces, and cones suit parts with holes. For parts with complex geometry, combining different shapes results in optimal finishing.

Compounds improve the efficiency of media, and they can also increase the foam level or lubrication inside the machine to polish the parts. Another function is to improve the grinding effect, which results in better deburring and smoothing. Vibra Finish recommends compounds for degreasing and cleaning applications, since they help to emulsify and suspend dirt, while also removing scale. Another major advantage is imparting anti-rust and anti-corrosion properties on components to lengthen their lifespans.

Finishing compounds typically come in liquid, powder, or cream form, each made out of ingredients in varying proportions to give them a distinct acidic, alkaline, or pH-balanced property.

Our Products

STEEL MEDIA

Vibra Finishing Solutions

STEEL MEDIA

Challenges we’ve solved in the past

Background

Past Research

Commercial Components and Vibratory Peening

Gear

Blade

Conclusions and Future Steps

About Vibra Finish

Request A Quote